Solved Exercises on Measuring and Drawing Angles in Grade 4

Master angle measurement and construction: identifying types, measuring with protractor, and drawing precise angles through these 5 detailed exercises.

Angle Concepts & Tools
📐 1° = 1 degree
Angle Measurement Unit
Key Definitions:

Angle: The space between two rays that meet at a point (vertex)

Protractor: A semicircular tool used to measure angles in degrees

Vertex: The point where two rays meet to form an angle

Ray: A line that starts at a point and extends infinitely in one direction

Acute Angle
0° < angle < 90°
Less than right angle
Right Angle
angle = 90°
Perfect corner
Obtuse Angle
90° < angle < 180°
Greater than right angle
Straight Angle
angle = 180°
Forms a straight line
Measuring Angles with Protractor:
  1. Position: Place center of protractor on angle's vertex
  2. Align: Align baseline with one ray of the angle
  3. Read: Follow other ray to degree marking
  4. Choose Scale: Use inner or outer scale based on angle direction
Drawing Angles with Protractor:
  1. Draw Base: Create a straight line (baseline)
  2. Mark Vertex: Choose point on line as angle's vertex
  3. Position Protractor: Center on vertex, baseline aligned
  4. Mark Degree: Locate desired angle measurement
  5. Draw Ray: Connect vertex to marked point
Tip 1: Always estimate angle type before measuring.
Tip 2: Check if your measurement matches the angle's appearance.
Tip 3: Extend rays if they're too short for accurate measurement.
Solution: Exercises 1 to 3
1 Measuring an Acute Angle
Exercise 1
Measure an angle that appears narrow and opens to the right.
Definition:

Acute Angle: An angle measuring less than 90°

Measurement Method:
  1. Place protractor center on angle's vertex
  2. Align baseline with the lower ray
  3. Read measurement where upper ray crosses scale
  4. Use inner scale (reading left to right)
Step 1: Position protractor

Center hole goes over vertex where rays meet

Step 2: Align baseline

Bottom edge aligns with lower ray at 0°

Step 3: Read measurement

Upper ray crosses at 35° on inner scale

Step 4: Verify reasonableness

35° < 90°, confirming it's acute

35°
Angle measures 35°
Final Answer:

The angle measures 35° and is an acute angle

Applied Rules:

• Protractor center on vertex

• Baseline aligned with one ray

• Inner scale for angles opening right

• Acute: 0° < angle < 90°

2 Measuring an Obtuse Angle
Exercise 2
Measure an angle that appears wide and opens to the left.
Definition:

Obtuse Angle: An angle measuring more than 90° but less than 180°

Measurement Method:
  1. Place protractor center on angle's vertex
  2. Align baseline with the lower ray
  3. Read measurement where upper ray crosses scale
  4. Use outer scale (reading right to left)
Step 1: Position protractor

Center hole goes over vertex where rays meet

Step 2: Align baseline

Bottom edge aligns with lower ray at 0°

Step 3: Read measurement

Upper ray crosses at 145° on outer scale

Step 4: Verify reasonableness

90° < 145° < 180°, confirming it's obtuse

145°
Angle measures 145°
Final Answer:

The angle measures 145° and is an obtuse angle

Applied Rules:

• Protractor center on vertex

• Baseline aligned with one ray

• Outer scale for angles opening left

• Obtuse: 90° < angle < 180°

3 Drawing a Specific Angle
Exercise 3
Draw an angle that measures exactly 75°.
Definition:

Angle Construction: Creating an angle of specific measure using protractor

Construction Method:
  1. Draw a straight baseline
  2. Mark a point on the line as the vertex
  3. Position protractor with center on vertex
  4. Mark the 75° point on the scale
  5. Draw a ray from vertex through the 75° mark
Step 1: Draw baseline

Draw a horizontal line segment

Step 2: Mark vertex

Place a point on the line to serve as the angle's vertex

Step 3: Position protractor

Center on vertex, baseline aligned with 0°

Step 4: Mark 75°

Locate 75° on the scale and make a small mark

Step 5: Draw the angle

Connect vertex to the 75° mark with a straight line

75°
Constructed angle = 75°
Final Answer:

Successfully constructed a 75° angle

Applied Rules:

• Start with baseline and vertex

• Center protractor on vertex

• Mark exact degree measurement

• Draw straight line to complete angle

Solution: Exercises 4 to 5
4 Comparing and Verifying Angles
Exercise 4
You drew an angle measuring 120°. Another student drew an angle measuring 60°. How much larger is your angle?
Definition:

Angle Comparison: Finding the difference between two angle measures

Comparison Method:
  1. Identify both angle measurements
  2. Subtract the smaller angle from the larger
  3. Express the difference in degrees
  4. Verify the calculation
Step 1: Identify measurements

Your angle: 120°, Other student's angle: 60°

Step 2: Subtract smaller from larger

120° - 60° = 60°

Step 3: Express difference

Your angle is 60° larger than the other student's

Step 4: Verify calculation

60° + 60° = 120° ✓

60°
120°
Your angle is 60° larger
Final Answer:

Your angle is 60° larger than the other student's angle

Applied Rules:

• Angle comparison: Larger - Smaller = Difference

• Both angles share common vertex and baseline

5 Real-World Application
Exercise 5
A skateboard ramp needs to be built with a 30° incline. If the horizontal length is 4 feet, what angle should the ramp make with the ground?
Definition:

Real-World Application: Applying angle measurements to practical construction problems

Problem-Solving Method:
  1. Identify the required angle from specifications
  2. Understand the relationship between angle and dimensions
  3. Apply the specified angle to the construction
  4. Verify the angle meets requirements
Step 1: Identify required angle

The specifications call for a 30° incline

Step 2: Understand the relationship

Horizontal length affects the steepness of the 30° angle

Step 3: Apply the angle

The ramp should form a 30° angle with the ground

Step 4: Verify requirements

30° is a moderate incline suitable for skateboarding

30°
Ground
Ramp
Ramp angle = 30° with ground
Final Answer:

The ramp should make a 30° angle with the ground to meet the specifications

Applied Rules:

• Real-world angle specifications must be precise

• Construction angles affect functionality

• 30° is a common angle for ramps

Questions & Answers

Question: I sometimes get confused about which scale to use on the protractor. How can I remember which one to read?

Answer: The key is to look at the direction your angle opens:

  • Inner Scale: Use when the angle opens to the right (clockwise from baseline)
  • Outer Scale: Use when the angle opens to the left (counterclockwise from baseline)

Always start reading from 0° where your baseline ray meets the protractor. The scale that starts at 0° is the one you should use! A helpful trick is to notice that the numbers increase in the direction your angle opens.

Question: What should I do if the rays of my angle are too short to reach the protractor's scale?

Answer: If your angle's rays are too short to reach the protractor's scale, extend them carefully:

  1. Use a ruler to extend both rays of the angle beyond where they intersect
  2. Make sure to maintain the same direction for each ray
  3. Now place your protractor and measure the extended rays
  4. Remember that extending rays doesn't change the angle's measure

Extending rays just makes it easier to measure accurately. The angle measurement remains the same regardless of ray length.

Question: How can I make sure my drawn angle is accurate when using a protractor?

Answer: Follow these accuracy checks:

  1. Position Check: Ensure the protractor's center is precisely on the vertex point
  2. Alignment Check: Make sure the baseline aligns perfectly with the starting ray
  3. Marking Check: Carefully mark the exact degree measurement on the scale
  4. Line Check: Use a ruler to draw a straight line from vertex to marked point
  5. Verification Check: Re-measure the angle to confirm accuracy

A good practice is to hold the protractor steady with one hand while marking with the other to prevent movement during the process.