Solved Exercises on Using a Protractor in Grade 4

Master angle measurement: identifying angle types, measuring degrees, calculating angle sums, and applying geometric principles through these 5 detailed exercises.

Protractor Guide & Key Concepts
🔍 Center on Vertex
Protractor Placement
Key Definitions:

Protractor: A semicircular tool used to measure angles in degrees

Vertex: The point where two rays meet to form an angle

Baseline: The straight edge of the protractor that aligns with one ray

Scale: The curved edge marked with degree measurements (0° to 180°)

Proper Protractor Use:
  1. Position: Place center hole over the angle's vertex
  2. Align: Align baseline with one ray of the angle
  3. Read: Follow the other ray to the degree marking
  4. Choose Scale: Use inner or outer scale depending on angle direction
Inner Scale
Read from left to right
For angles opening right
Outer Scale
Read from right to left
For angles opening left
Acute Angle
0° < angle < 90°
Narrow angle
Obtuse Angle
90° < angle < 180°
Wide angle
Tip 1: Always align the protractor's center with the angle's vertex.
Tip 2: Check if your measured angle matches its appearance (acute vs obtuse).
Tip 3: Use the scale that starts at 0° where your baseline ray meets the protractor.
Solution: Exercises 1 to 3
1 Measuring an Acute Angle
Exercise 1
Measure an angle that opens to the right and appears narrow.
Definition:

Acute Angle: An angle measuring less than 90°

Measurement Method:
  1. Place protractor center on angle vertex
  2. Align baseline with the lower ray
  3. Read measurement where upper ray crosses scale
  4. Use inner scale (reading left to right)
Step 1: Position protractor

Center hole goes over vertex where rays meet

Step 2: Align baseline

Bottom edge aligns with lower ray at 0°

Step 3: Read measurement

Upper ray crosses at 45° on inner scale

0°
45°
90°
Angle measures 45°
Final Answer:

The angle measures 45° and is an acute angle

Applied Rules:

• Protractor center on vertex

• Baseline aligned with one ray

• Inner scale for angles opening right

2 Measuring an Obtuse Angle
Exercise 2
Measure an angle that opens to the left and appears wide.
Definition:

Obtuse Angle: An angle measuring more than 90° but less than 180°

Measurement Method:
  1. Place protractor center on angle vertex
  2. Align baseline with the lower ray
  3. Read measurement where upper ray crosses scale
  4. Use outer scale (reading right to left)
Step 1: Position protractor

Center hole goes over vertex where rays meet

Step 2: Align baseline

Bottom edge aligns with lower ray at 0°

Step 3: Read measurement

Upper ray crosses at 135° on outer scale

0°
45°
135°
90°
Angle measures 135°
Final Answer:

The angle measures 135° and is an obtuse angle

Applied Rules:

• Protractor center on vertex

• Baseline aligned with one ray

• Outer scale for angles opening left

3 Drawing an Angle
Exercise 3
Draw an angle that measures 60°.
Definition:

Angle Construction: Creating an angle of specific measure using protractor

Construction Method:
  1. Draw a straight line (the baseline)
  2. Mark a point on the line as the vertex
  3. Place protractor with center on vertex and baseline aligned
  4. Mark the desired degree measurement
  5. Draw a line from vertex through the marked point
Step 1: Draw baseline

Draw a horizontal line segment

Step 2: Mark vertex

Make a point on the line to be the angle's vertex

Step 3: Position protractor

Center on vertex, baseline aligned with 0°

Step 4: Mark 60°

Find 60° on the scale and make a dot

Step 5: Draw the angle

Connect vertex to the 60° mark

0°
60°
90°
Constructed angle = 60°
Final Answer:

Successfully constructed a 60° angle

Applied Rules:

• Start with baseline and vertex

• Center protractor on vertex

• Mark exact degree measurement

Solution: Exercises 4 to 5
4 Verifying Angle Measures
Exercise 4
You measure an angle and get 110°. Verify this is reasonable for an obtuse angle.
Definition:

Reasonableness Check: Verifying that a measurement makes sense given the angle's appearance

Verification Method:
  1. Estimate the angle by sight
  2. Classify the angle type (acute, right, obtuse)
  3. Compare measurement to expected range
  4. Confirm measurement is within correct range
Step 1: Visual estimation

The angle appears wider than 90°

Step 2: Classification

This is an obtuse angle (greater than 90°)

Step 3: Range check

Obtuse angles: 90° < angle < 180°

Step 4: Verification

110° is between 90° and 180° ✓

0°
110°
90°
110° is reasonable for obtuse angle
Final Answer:

The measurement of 110° is reasonable as it falls within the obtuse angle range (90°-180°)

Applied Rules:

• Acute: 0° < angle < 90°

• Right: angle = 90°

• Obtuse: 90° < angle < 180°

5 Real-World Application
Exercise 5
A ramp makes an angle with the ground. You measure it as 25°. Is this safe for wheelchair access if safety guidelines require angles under 30°?
Definition:

Real-World Application: Applying angle measurements to practical situations

Problem-Solving Method:
  1. Measure the angle using proper protractor technique
  2. Compare measurement to safety requirement
  3. Determine if measurement meets criteria
  4. State conclusion with reasoning
Step 1: Measurement

Angle measured as 25° using protractor

Step 2: Safety requirement

Guidelines require angles under 30°

Step 3: Comparison

25° < 30°, so it meets requirements

Step 4: Conclusion

The ramp is safe for wheelchair access

0°
25°
30°
Ramp angle = 25° (safe for access)
Final Answer:

Yes, the 25° angle is safe for wheelchair access since it is less than the 30° maximum allowed.

Applied Rules:

• Accurate measurement using protractor

• Comparison to safety standards

• Practical application of angle measurements

Questions & Answers

Question: I'm confused about which scale to use on the protractor. How do I know when to use the inner or outer scale?

Answer: The key is to look at the direction your angle opens:

  • Inner Scale: Use when the angle opens to the right (clockwise from baseline)
  • Outer Scale: Use when the angle opens to the left (counterclockwise from baseline)

Always start reading from 0° where your baseline ray meets the protractor. The scale that starts at 0° is the one you should use!

Question: What should I do if the angle I'm measuring is too small to fit properly on my protractor?

Answer: If your angle's rays are too short to reach the protractor's scale, extend them:

  1. Use a ruler to extend both rays of the angle beyond where they intersect
  2. Make sure to maintain the same direction for each ray
  3. Now place your protractor and measure the extended rays

Extending rays doesn't change the angle's measure - it just makes it easier to measure accurately.

Question: How can I make sure my protractor is positioned correctly when measuring an angle?

Answer: Follow these positioning checks:

  1. Center Check: The small hole or mark in the center of the protractor must be directly over the angle's vertex
  2. Alignment Check: One ray of the angle must align perfectly with the baseline of the protractor
  3. Stability Check: Hold the protractor steady without moving while reading the measurement

A good trick is to hold the protractor with one hand and use the other to read the measurement, ensuring it doesn't shift during measurement.