y = 4x - 7
Slope-intercept form: y = mx + b where m is slope and b is y-intercept
Slope (m): The coefficient of x, representing rate of change
Y-intercept (b): The constant term, representing the value of y when x = 0
- Compare the given equation to the form y = mx + b
- Identify the coefficient of x as the slope (m)
- Identify the constant term as the y-intercept (b)
- Note: If the constant term is negative, the y-intercept is negative
y = 4x - 7 compared to y = mx + b
m corresponds to the coefficient of x
b corresponds to the constant term
In y = 4x - 7, the coefficient of x is 4
Therefore, slope m = 4
This means the line rises 4 units for every 1 unit it moves to the right
In y = 4x - 7, the constant term is -7
Therefore, y-intercept b = -7
This means the line crosses the y-axis at the point (0, -7)
When x = 0: y = 4(0) - 7 = -7
So the point (0, -7) is on the line, confirming our y-intercept
• Slope-intercept form: y = mx + b identifies m and b directly
• Y-intercept definition: Value of y when x = 0
• Coefficient identification: Number multiplied by x is the slope
y = -⅓x + 5
Fractional slope: When slope is expressed as a fraction, it represents rise over run
Negative slope: When slope is negative, the line decreases from left to right
y = -⅓x + 5 compared to y = mx + b
Notice the negative sign in front of the fraction
In y = -⅓x + 5, the coefficient of x is -⅓
Therefore, slope m = -⅓
This means the line falls 1 unit for every 3 units it moves to the right
In y = -⅓x + 5, the constant term is +5
Therefore, y-intercept b = 5
This means the line crosses the y-axis at the point (0, 5)
Slope = -⅓ means: for every 3 units right, go down 1 unit
Or equivalently: for every 1 unit right, go down ⅓ unit
• Fractional slopes: Express as rise over run (numerator/denominator)
• Negative slopes: Line decreases from left to right
• Sign importance: Always include the sign when identifying coefficients
2x + 3y = 12
Standard form: Ax + By = C (not in slope-intercept form)
Conversion needed: Must solve for y to identify slope and y-intercept
2x + 3y = 12 is in standard form, not slope-intercept form
We need to solve for y to identify m and b
2x + 3y = 12
Subtract 2x from both sides: 3y = -2x + 12
Divide every term by 3: y = (-2x + 12)/3
y = -2x/3 + 12/3
y = -⅔x + 4
In y = -⅔x + 4, comparing to y = mx + b:
Slope m = -⅔
Y-intercept b = 4
Substitute back: 2x + 3(-⅔x + 4) = 2x - 2x + 12 = 12 ✓
• Standard to slope-intercept: Solve for y to isolate it
• Algebraic manipulation: Perform same operation on both sides
• Division property: Divide each term by the coefficient of y
Slope (m): Measure of steepness and direction of a line
Y-intercept (b): Point where line crosses the y-axis (x = 0)
Rate of change: How much y changes when x increases by 1
Linear function: Function whose graph is a straight line
- Slope-intercept form: Directly read m and b from y = mx + b
- Standard form: Convert to slope-intercept by solving for y
- Two points: Use slope formula then point-slope form
- Graph: Visually identify y-intercept and calculate slope
Complete Learning Summary
Slope (m): The coefficient of x in y = mx + b. Represents the rate of change and steepness of a line. Calculated as rise over run: (y₂ - y₁)/(x₂ - x₁)
Y-intercept (b): The constant term in y = mx + b. The value of y when x = 0. The point where the line crosses the y-axis (0, b).
Slope-intercept form: The equation y = mx + b where m is slope and b is y-intercept. This form directly shows both values.
Rule 1: In y = mx + b, m is always the coefficient of x and b is always the constant term.
Rule 2: Signs matter! If y = -3x + 5, then m = -3 (negative slope) and b = 5 (positive y-intercept).
Rule 3: When converting from standard form (Ax + By = C), solve for y to get slope-intercept form.
Rule 4: Always check your work by substituting x = 0 to verify the y-intercept.
Method 1 (Direct Identification): When equation is in y = mx + b form, directly read m and b.
Method 2 (Conversion): When equation is in standard form Ax + By = C, solve for y to get y = mx + b form.
Method 3 (Verification): Substitute x = 0 into the original equation to confirm y-intercept.
Method 4 (Graphical): Plot the y-intercept and use slope to find another point.
Simple example: y = 2x + 3 → m = 2, b = 3
Fractional slope: y = -¼x + 7 → m = -¼, b = 7
Negative y-intercept: y = 5x - 8 → m = 5, b = -8
Standard form: 3x + 2y = 6 → y = -3/2x + 3 → m = -3/2, b = 3
Tip 1: Always pay attention to signs! Don't confuse -3x with +3x.
Tip 2: When converting standard form, divide EVERY term by the coefficient of y.
Mistake 1: Forgetting the sign of the y-intercept when it's negative.
Mistake 2: Not fully converting to slope-intercept form before identifying m and b.
Memory trick: "y = mx + b" → "y equals m-x plus b" (slope first, then y-intercept).
Visualization: Think of m as "move" (how the line moves) and b as "beginning" (where it starts on y-axis).
Verification: Always substitute x = 0 to check that y equals your identified y-intercept.
Pattern recognition: Look for the pattern y = (number)x + (number) to quickly identify m and b.