Linear equation: An equation that forms a straight line when graphed
Slope-intercept form: y = mx + b where m is slope and b is y-intercept
Slope (m): Rate of change, rise over run
Y-intercept (b): Point where line crosses y-axis (when x = 0)
- Identify slope (m) and y-intercept (b) from y = mx + b
- Plot the y-intercept (0, b) on the y-axis
- Use the slope to find additional points
- Draw a straight line through the points
y = 2x + 3 is in slope-intercept form y = mx + b
Slope (m) = 2, Y-intercept (b) = 3
Y-intercept is the point (0, 3)
This is where the line crosses the y-axis
Slope = 2 means rise of 2 units for every 1 unit run
Starting from (0, 3), move right 1 and up 2 → (1, 5)
From (1, 5): move right 1 and up 2 → (2, 7)
From (0, 3): move left 1 and down 2 → (-1, 1)
Connect all points with a straight line extending in both directions
• Slope-intercept form: y = mx + b identifies m and b directly
• Slope as rise/run: Move vertically by rise, horizontally by run
• Y-intercept: Value of y when x = 0
Negative slope: Line that decreases from left to right
Fractional slope: Slope expressed as a fraction, affecting rise/run
y = -½x + 4 → slope m = -½, y-intercept b = 4
The negative slope means the line falls as it moves right
Y-intercept is the point (0, 4)
Slope = -½ means rise of -1 (fall of 1) for every run of 2
Starting from (0, 4), move right 2 and down 1 → (2, 3)
From (2, 3): move right 2 and down 1 → (4, 2)
From (0, 4): move left 2 and up 1 → (-2, 5)
Connect points with a straight line that slopes downward from left to right
• Negative slope: Line decreases from left to right
• Fractional slope: Convert to whole number movements if needed
• Consistency: All points must satisfy the original equation
Standard form: Ax + By = C (not in slope-intercept form)
Conversion: Solve for y to get y = mx + b form
Start with: 2x + 3y = 12
Subtract 2x from both sides: 3y = -2x + 12
Divide by 3: y = -⅔x + 4
y = -⅔x + 4 → slope m = -⅔, y-intercept b = 4
Y-intercept is the point (0, 4)
Slope = -⅔ means rise of -2 (fall of 2) for every run of 3
Starting from (0, 4), move right 3 and down 2 → (3, 2)
From (3, 2): move right 3 and down 2 → (6, 0)
From (0, 4): move left 3 and up 2 → (-3, 6)
• Standard to slope-intercept: Solve for y to identify m and b
• Fractional slopes: Handle carefully, considering both numerator and denominator
• Verification: Substitute points back into original equation
Slope (m): Rate of change, calculated as rise/run or (change in y)/(change in x)
Y-intercept (b): Point where line crosses y-axis (x = 0)
Linear equation: Equation that graphs as a straight line
X-intercept: Point where line crosses x-axis (y = 0)
- Slope-Intercept Method: Use y-intercept and slope
- Intercept Method: Find x and y intercepts
- Table Method: Create input-output table
- Point-Slope Method: Use known point and slope
Complete Learning Summary
Linear equation: An equation that forms a straight line when graphed, typically in the form y = mx + b.
Slope (m): The measure of steepness of a line, calculated as the ratio of vertical change (rise) to horizontal change (run).
Y-intercept (b): The point where the line crosses the y-axis, occurring when x = 0.
X-intercept: The point where the line crosses the x-axis, occurring when y = 0.
Slope-intercept form: The form y = mx + b, which directly shows the slope and y-intercept.
Rule 1: The slope formula is m = (y₂ - y₁)/(x₂ - x₁) for any two points on the line.
Rule 2: In y = mx + b, m represents the slope and b represents the y-intercept.
Rule 3: A linear equation graphs as a straight line that extends infinitely in both directions.
Rule 4: Two points are sufficient to determine a unique line.
Rule 5: The slope remains constant along the entire line.
Method 1 (Slope-Intercept): Identify m and b, plot y-intercept, use slope to find additional points.
Method 2 (Intercept): Find x-intercept (set y=0) and y-intercept (set x=0), connect the points.
Method 3 (Conversion): Convert from standard form to slope-intercept form by solving for y.
Method 4 (Verification): Substitute points back into the original equation to confirm accuracy.
Simple example: y = 2x + 1 → slope = 2, y-intercept = 1
Fractional slope: y = ½x - 3 → slope = ½, y-intercept = -3
Negative slope: y = -3x + 4 → slope = -3, y-intercept = 4
Standard form: 3x + 2y = 6 → y = -3/2x + 3 → slope = -3/2, y-intercept = 3
Tip 1: Always identify slope and y-intercept before graphing.
Tip 2: Remember that negative slopes create decreasing lines from left to right.
Mistake 1: Confusing rise and run in slope calculations.
Mistake 2: Forgetting to convert standard form equations to slope-intercept form.
Memory trick: "y equals m-x plus b" - slope first, then y-intercept.
Visualization: Think of slope as "how much to move up/down" for "each step right".
Pattern recognition: Look for the y = mx + b pattern to quickly identify slope and y-intercept.
Verification: Always check that your points satisfy the original equation.