Solved Exercises on Composite Solids in Grade 8

Master composite solids: volume, surface area, and decomposition methods through these 10 detailed exercises.

Solution: Exercises 1 to 3
1 Rectangular Prism and Cube
Exercise 1
Find the volume of a composite solid made of a rectangular prism (4 cm × 3 cm × 5 cm) attached to a cube (2 cm × 2 cm × 2 cm) on top.
Definition:

Composite Solid: A three-dimensional figure composed of two or more basic geometric solids. Volume of composite solid = sum of individual volumes.

Volume calculation method:
  1. Identify the basic solids that make up the composite solid
  2. Calculate the volume of each basic solid separately
  3. Add the volumes together to get the total volume
  4. Ensure all measurements are in the same units
Prism dimensions
4×3×5 cm
Cube dimensions
2×2×2 cm
Step 1: Calculate volume of rectangular prism

Volume of prism = length × width × height = 4 × 3 × 5 = 60 cm³

Step 2: Calculate volume of cube

Volume of cube = side³ = 2³ = 8 cm³

Step 3: Add the volumes

Total volume = Volume of prism + Volume of cube = 60 + 8 = 68 cm³

Total volume = 68 cm³
Final answer:

The volume of the composite solid is 68 cubic centimeters.

Applied rules:

• Volume Addition: V_total = V_1 + V_2 + ... for non-overlapping solids

• Rectangular Prism: V = lwh

• Cube: V = s³

2 Cylinder and Cone
Exercise 2
Find the volume of a composite solid made of a cylinder (radius 3 cm, height 8 cm) with a cone (same radius, height 4 cm) on top.
Definition:

Composite Solid with Curved Surfaces: When combining curved surfaces like cylinders and cones, use the appropriate volume formulas and add them.

Cylinder
r=3, h=8 cm
Cone
r=3, h=4 cm
Step 1: Calculate volume of cylinder

Volume of cylinder = πr²h = π × 3² × 8 = π × 9 × 8 = 72π cm³

Step 2: Calculate volume of cone

Volume of cone = (1/3)πr²h = (1/3) × π × 3² × 4 = (1/3) × π × 9 × 4 = 12π cm³

Step 3: Add the volumes

Total volume = 72π + 12π = 84π cm³ ≈ 263.89 cm³

Total volume = 84π cm³ ≈ 263.89 cm³
Final answer:

The volume of the composite solid is 84π cubic centimeters or approximately 263.89 cubic centimeters.

Applied rules:

• Cylinder Volume: V = πr²h

• Cone Volume: V = (1/3)πr²h

• Volume Addition: Sum of individual volumes

3 Surface Area of L-shaped Solid
Exercise 3
Find the surface area of an L-shaped solid formed by two rectangular prisms: base (6 cm × 4 cm × 2 cm) and vertical arm (2 cm × 4 cm × 3 cm) attached to the center of the base.
Definition:

Surface Area of Composite Solid: The total area of all exposed surfaces. When solids are joined, subtract the overlapping areas.

Base prism
6×4×2 cm
Vertical arm
2×4×3 cm
Step 1: Calculate surface area of base prism

SA_base = 2(lw + lh + wh) = 2(6×4 + 6×2 + 4×2) = 2(24 + 12 + 8) = 2(44) = 88 cm²

Step 2: Calculate surface area of vertical prism

SA_arm = 2(lw + lh + wh) = 2(2×4 + 2×3 + 4×3) = 2(8 + 6 + 12) = 2(26) = 52 cm²

Step 3: Subtract overlapping area

When the vertical arm is attached to the base, the touching faces are no longer exposed. The overlapping area is 2×4 = 8 cm² on each solid = 16 cm² total to subtract.

Step 4: Calculate total surface area

Total SA = SA_base + SA_arm - 2(overlapping area) = 88 + 52 - 16 = 124 cm²

Total surface area = 124 cm²
Final answer:

The surface area of the L-shaped solid is 124 square centimeters.

Applied rules:

• Surface Area Formula: SA = 2(lw + lh + wh) for rectangular prism

• Overlap Subtraction: Subtract twice the joining area

• Exposed Surfaces: Only count surfaces visible from outside

Solution: Exercises 4 to 6
4 Hollow Cylinder
Exercise 4
Find the volume of a hollow cylinder with outer radius 5 cm, inner radius 3 cm, and height 10 cm.
Definition:

Hollow Cylinder: A composite solid formed by subtracting a smaller cylinder from a larger cylinder. Volume = Volume_outer - Volume_inner.

Outer cylinder
r=5, h=10 cm
Inner cylinder
r=3, h=10 cm
Step 1: Calculate volume of outer cylinder

Volume_outer = πR²h = π × 5² × 10 = π × 25 × 10 = 250π cm³

Step 2: Calculate volume of inner cylinder

Volume_inner = πr²h = π × 3² × 10 = π × 9 × 10 = 90π cm³

Step 3: Subtract inner volume from outer volume

Volume_hollow = Volume_outer - Volume_inner = 250π - 90π = 160π cm³ ≈ 502.65 cm³

Volume = 160π cm³ ≈ 502.65 cm³
Final answer:

The volume of the hollow cylinder is 160π cubic centimeters or approximately 502.65 cubic centimeters.

Applied rules:

• Hollow Volume: V = π(R² - r²)h

• Subtraction Method: Subtract inner solid from outer solid

• Annular Cross-Section: Cross-section is a ring (annulus)

5 Pyramid on Rectangular Base
Exercise 5
Find the volume of a composite solid consisting of a rectangular prism (8 cm × 6 cm × 4 cm) with a square pyramid (base 6 cm × 6 cm, height 5 cm) on top, where the pyramid base is centered on the prism top face.
Definition:

Prism and Pyramid Composite: Combine a rectangular prism with a pyramid. Calculate each volume separately and add them together.

Prism
8×6×4 cm
Pyramid
base 6×6, h=5 cm
Step 1: Calculate volume of rectangular prism

Volume_prism = lwh = 8 × 6 × 4 = 192 cm³

Step 2: Calculate volume of square pyramid

Volume_pyramid = (1/3)Bh = (1/3) × (6 × 6) × 5 = (1/3) × 36 × 5 = 60 cm³

Step 3: Add the volumes

Total volume = Volume_prism + Volume_pyramid = 192 + 60 = 252 cm³

Total volume = 252 cm³
Final answer:

The volume of the composite solid is 252 cubic centimeters.

Applied rules:

• Prism Volume: V = lwh

• Pyramid Volume: V = (1/3)Bh

• Volume Addition: Sum of individual volumes

6 Sphere Inside Cube
Exercise 6
Find the volume of empty space in a cube (side length 6 cm) with a sphere (diameter 6 cm) perfectly fitted inside.
Definition:

Empty Space in Composite: When one solid is inside another, the empty space is the difference between their volumes: Empty Space = V_outer - V_inner.

Cube
side = 6 cm
Sphere
diameter = 6 cm
Step 1: Calculate volume of cube

Volume_cube = s³ = 6³ = 216 cm³

Step 2: Calculate volume of sphere

Radius of sphere = diameter/2 = 6/2 = 3 cm

Volume_sphere = (4/3)πr³ = (4/3) × π × 3³ = (4/3) × π × 27 = 36π cm³ ≈ 113.10 cm³

Step 3: Calculate empty space

Empty space = Volume_cube - Volume_sphere = 216 - 36π ≈ 216 - 113.10 = 102.90 cm³

Empty space ≈ 102.90 cm³
Final answer:

The volume of empty space in the cube is 216 - 36π cubic centimeters or approximately 102.90 cubic centimeters.

Applied rules:

• Cube Volume: V = s³

• Sphere Volume: V = (4/3)πr³

• Subtraction Method: Empty space = V_outer - V_inner

Rules and methods, laws,...
\(V_{total} = \sum V_i\)
Total Volume of Composite Solid
\(SA_{total} = \sum SA_i - 2 \times SA_{overlap}\)
Total Surface Area with Overlap
RECTANGULAR
CYLINDER
SPHERE
V=lwh
V=πr²h
V=(4/3)πr³
Key definitions:

Composite Solid: A three-dimensional figure made by combining two or more basic geometric solids

Volume: The amount of space occupied by a three-dimensional figure

Surface Area: The total area of all exposed surfaces of a three-dimensional figure

Basic Solids: Prisms, pyramids, cylinders, cones, spheres, and hemispheres

Composite solid methodology:
  1. Identify components: Break down the composite solid into recognizable basic solids
  2. Select formulas: Choose appropriate volume/surface area formulas for each component
  3. Calculate individually: Find the measurement for each component
  4. Combine appropriately: Add volumes, adjust surface areas for overlaps
Tip 1: Sketch the composite solid and label dimensions to visualize components.
Tip 2: For surface area, subtract areas where solids join together.
Tip 3: Keep work organized by calculating each component separately.
Common errors: Forgetting to subtract overlapping areas, using wrong formulas, unit mismatches.
Key principle: Volume adds, but surface area requires adjustment for joins.
Composite Solids: Comprehensive Guide
Decomposition Strategy
STEP 1
IDENTIFY
Recognize basic solids
STEP 2
MEASURE
Get dimensions
STEP 3
CALCULATE
Individual volumes
STEP 4
COMBINE
Add or subtract
Volume Formulas
🧱
Prism: V = Bh (Base Area × Height)
🔺
Pyramid: V = (1/3)Bh
🛢️
Cylinder: V = πr²h
cono
Cone: V = (1/3)πr²h
⚽
Sphere: V = (4/3)πr³
Calculation Examples
Rectangular Prism
V = lwh
3×4×5=60 cm³
Cylinder
V = πr²h
π×2²×6≈75.4 cm³
Hollow Cylinder
V = π(R²-r²)h
π×(5²-3²)×8≈402.1 cm³
Pyramid
V = (1/3)Bh
(1/3)×9×6=18 cm³
Surface Area Considerations
JOINING
Solid₁ + Solid₂
→
SURFACE AREA
SA₁ + SA₂ - 2×Overlap
=
RESULT
Combined SA
✓
Important Properties
  • Volumes always add together when combining solids
  • Surface areas require subtracting overlapping regions
  • Dimensions must be consistent across all calculations
  • Visualizing the composite helps identify components
  • Always check units in final answer
Solution: Exercises 7 to 9
7 T-shaped Solid
Exercise 7
Find the volume of a T-shaped solid formed by a horizontal rectangular prism (10 cm × 4 cm × 2 cm) with a vertical prism (4 cm × 4 cm × 6 cm) centered on top.
Definition:

T-shaped Composite Solid: A configuration where one prism extends perpendicularly from the center of another, forming a T-shape. Calculate volumes separately and add them.

Horizontal prism
10×4×2 cm
Vertical prism
4×4×6 cm
Step 1: Calculate volume of horizontal prism

Volume_horizontal = lwh = 10 × 4 × 2 = 80 cm³

Step 2: Calculate volume of vertical prism

Volume_vertical = lwh = 4 × 4 × 6 = 96 cm³

Step 3: Add the volumes

Since the prisms are joined but don't overlap in volume, Total volume = 80 + 96 = 176 cm³

Total volume = 176 cm³
Final answer:

The volume of the T-shaped solid is 176 cubic centimeters.

Applied rules:

• Volume Addition: V_total = V_1 + V_2 for non-overlapping solids

• Rectangular Prism: V = lwh

• Component Analysis: Treat each part separately

8 Cylindrical Hole in Rectangular Prism
Exercise 8
Find the volume of a rectangular prism (8 cm × 6 cm × 4 cm) with a cylindrical hole (radius 1 cm, going through the entire height of 4 cm) drilled through its center.
Definition:

Solid with Cavity: When a hole is drilled through a solid, subtract the volume of the hole from the original solid's volume.

Prism
8×6×4 cm
Cylindrical hole
r=1, h=4 cm
Step 1: Calculate volume of rectangular prism

Volume_prism = lwh = 8 × 6 × 4 = 192 cm³

Step 2: Calculate volume of cylindrical hole

Volume_cylinder = πr²h = π × 1² × 4 = 4π cm³ ≈ 12.57 cm³

Step 3: Subtract hole volume from prism volume

Net volume = Volume_prism - Volume_hole = 192 - 4π ≈ 192 - 12.57 = 179.43 cm³

Net volume ≈ 179.43 cm³
Final answer:

The volume of the solid with the cylindrical hole is 192 - 4π cubic centimeters or approximately 179.43 cubic centimeters.

Applied rules:

• Subtraction Method: V_net = V_original - V_removed

• Cylinder Volume: V = πr²h

• Cavity Principle: Remove volume of internal voids

9 Stacked Cylinders
Exercise 9
Find the total surface area of two cylinders stacked vertically: bottom (radius 3 cm, height 5 cm) and top (radius 2 cm, height 4 cm), where the top cylinder sits centered on the bottom cylinder.
Definition:

Stacked Cylinders Surface Area: Calculate individual surface areas, then subtract overlapping areas where the cylinders touch.

Bottom cylinder
r=3, h=5 cm
Top cylinder
r=2, h=4 cm
Step 1: Calculate surface area of bottom cylinder

SA_bottom = 2πr² + 2πrh = 2π(3²) + 2π(3)(5) = 18π + 30π = 48π cm²

Step 2: Calculate surface area of top cylinder

SA_top = 2πr² + 2πrh = 2π(2²) + 2π(2)(4) = 8π + 16π = 24π cm²

Step 3: Identify overlapping area

When the top cylinder sits on the bottom, the contact area is the top cylinder's base: π(2²) = 4π cm². This area is no longer exposed on the bottom cylinder's top face.

Step 4: Calculate total surface area

Total SA = SA_bottom + SA_top - 2(contact area) = 48π + 24π - 2(4π) = 72π - 8π = 64π cm² ≈ 201.06 cm²

Total surface area = 64π cm² ≈ 201.06 cm²
Final answer:

The total surface area of the stacked cylinders is 64π square centimeters or approximately 201.06 square centimeters.

Applied rules:

• Cylinder Surface Area: SA = 2πr² + 2πrh

• Overlap Subtraction: Subtract twice the contact area

• Exposed Surfaces: Only count surfaces visible from outside

Solution: Exercise 10
10 Complex Composite with Cutout
Exercise 10
A cube (side length 10 cm) has a cylindrical hole (diameter 4 cm) going through its center from top to bottom. A cone (base radius 3 cm, height 6 cm) is mounted on top of the hole. Find the total volume.
Definition:

Multi-component Composite: A solid with both added and subtracted components. Calculate each component's contribution separately, then combine with appropriate addition or subtraction.

Cube
side = 10 cm
Cylindrical hole
d=4, h=10 cm
Cone
r=3, h=6 cm
Step 1: Calculate volume of cube

Volume_cube = s³ = 10³ = 1,000 cm³

Step 2: Calculate volume of cylindrical hole

Radius of hole = 4/2 = 2 cm

Volume_hole = πr²h = π × 2² × 10 = 40π cm³ ≈ 125.66 cm³

Step 3: Calculate volume of cone

Volume_cone = (1/3)πr²h = (1/3) × π × 3² × 6 = (1/3) × π × 9 × 6 = 18π cm³ ≈ 56.55 cm³

Step 4: Combine volumes

Total volume = Volume_cube - Volume_hole + Volume_cone = 1,000 - 40π + 18π = 1,000 - 22π ≈ 1,000 - 69.12 = 930.88 cm³

Total volume ≈ 930.88 cm³
Final answer:

The total volume of the composite solid is 1,000 - 22π cubic centimeters or approximately 930.88 cubic centimeters.

Applied rules:

• Component Combination: Add volumes of added parts, subtract volumes of removed parts

• Multi-step Calculation: Handle each component separately

• Order of Operations: Properly combine additions and subtractions

Comprehensive Summary: Composite Solids
Definitions and Key Concepts

Composite Solid: A three-dimensional figure composed of two or more basic geometric solids combined together. These can be joined, stacked, nested, or have parts removed.

Volume: The amount of space inside a three-dimensional figure, measured in cubic units. For composite solids, volumes of individual components are added together.

Surface Area: The total area of all exposed surfaces of a three-dimensional figure, measured in square units. For composite solids, surface areas require careful consideration of overlapping regions.

Basic Components: The fundamental shapes that make up composite solids: rectangular prisms, cylinders, spheres, cones, pyramids, etc.

Core Rules and Principles

Volume Addition: V_total = Σ(V_i) for non-overlapping components. When solids are joined, their volumes add together.

Surface Area Adjustment: SA_total = Σ(SA_i) - 2 × Σ(overlap_areas). When solids join, subtract twice the overlapping area (once from each solid).

Subtraction Principle: When a cavity or hole exists, subtract its volume from the original solid: V_net = V_original - V_removed.

Unit Consistency: All measurements must be in the same units before performing calculations.

Step-by-Step Calculation Method
  1. Visualization: Sketch the composite solid and identify the basic shapes that compose it.
  2. Measurement: Label all necessary dimensions for each component.
  3. Formula Selection: Choose appropriate volume/surface area formulas for each component.
  4. Individual Calculations: Calculate the required measurement for each component separately.
  5. Combination: Add volumes together, adjust surface areas for overlaps or cavities.
  6. Verification: Check that units are consistent and answer is reasonable.
Examples from Simple to Advanced

Simple Join: Two rectangular prisms placed side by side: V_total = V_1 + V_2

Stacked Solids: Cylinder with cone on top: V_total = V_cylinder + V_cone

Hollow Shape: Cube with spherical cavity: V_total = V_cube - V_sphere

L-Shape: Two rectangular prisms forming an L: V_total = V_1 + V_2

Advanced Composite: Multiple operations like a solid with holes and added components

Tips, Tricks, and Common Pitfalls

Tips: Always draw a diagram to visualize the composite solid. Break complex shapes into simpler components. Keep work organized with clear labeling.

Tricks: For surface area, imagine painting the object - count only surfaces that would be painted. Use the principle that volumes always add, but surface areas often require subtraction.

Common Pitfalls: Forgetting to subtract overlapping areas for surface area calculations, using wrong formulas for components, mismatched units, not accounting for cavities properly.

Key Notes for Memorization

Memory Aid: "Volumes add, surfaces often subtract overlaps."

Formula Set: V_rectangular_prism = lwh, V_cylinder = πr²h, V_sphere = (4/3)πr³, V_cone = (1/3)πr²h

Golden Rule: Always consider what surfaces are exposed when calculating surface area.

Process: Identify → Measure → Calculate → Combine.

Explanation for Students

Think of composite solids like building with blocks or cookie dough. When you put two pieces of playdough together, the total amount of playdough (volume) increases, but some surfaces are no longer exposed where they touch (surface area). When you cut a hole through a block, you remove some material, decreasing the volume. The key is to break down complex shapes into familiar ones you know how to measure, then combine the results appropriately. Volume is like filling the shape with water - all the parts contribute. Surface area is like wrapping paper - only the outside counts, and where shapes join, there's less surface to wrap.

Questions & Answers

Question: How do I calculate the surface area of composite solids? Why do I sometimes subtract areas?

Answer: Surface area calculation for composite solids requires careful attention to which surfaces are exposed:

  • Exposed surfaces: These are the surfaces you can touch or paint
  • Hidden surfaces: Where solids join together, some surfaces become internal and are no longer part of the external surface area
  • Subtraction rule: When two solids are joined, subtract twice the area of their contact surface (once from each solid's surface area)

Imagine gluing two cubes together - the faces that touch are no longer exposed, so you subtract those areas from the total surface area calculation.

Question: When a shape has a hole drilled through it, how do I calculate the volume? Do I subtract the hole's volume?

Answer: Yes, when a solid has a hole or cavity, you subtract the hole's volume from the original solid's volume:

  • Start with full volume: Calculate the volume of the solid as if there were no hole
  • Calculate hole volume: Find the volume of the removed material
  • Subtract: Net volume = Original volume - Hole volume

For example, if you drill a cylindrical hole through a rectangular block, the remaining volume is the block's original volume minus the cylinder's volume. The hole removes material, so it reduces the total volume.

This is different from surface area, where holes might actually increase the surface area due to the new internal surfaces created.

Question: How do I know which formula to use for different parts of a composite solid?

Answer: Identify the basic geometric shape of each component:

  • Rectangular prism/cube: V = lwh, SA = 2(lw + lh + wh)
  • Cylinder: V = πr²h, SA = 2πr² + 2πrh
  • Sphere: V = (4/3)πr³, SA = 4πr²
  • Cone: V = (1/3)πr²h, SA = πr² + πrl
  • Pyramid: V = (1/3)Bh, where B is base area

Look at each part of the composite solid and match it to the closest basic shape. Practice recognizing these shapes in different orientations. When in doubt, break the composite into simpler parts that match known formulas.

Always ensure your dimensions match the requirements of the formula (e.g., radius vs diameter for circular shapes).